Product Selection Guide Page 805 Product Selection Guide-11th Edition

805 PSG11 LITHONIA LIGHTING OUTDOOR www.lithonia.com PRODUCT INFORMATION POLES Aluminum SSAH Square Straight Aluminum, Hinged ADDITIONAL INFORMATION For ordering information, see page 786. For additional product information, visit www.lithonia.com. TECHNICAL INFORMATION- EPA (FT 2 ) WITH 1.3 GUST (PLEASE SEE WIND MAP ON PAGE 788) CATALOG NUMBER NOM. MOUNT. HT. (FT.) POLE SHAFT SIZE (IN. X FT.) WALL THICK. (IN.) 80 MPH 90 MPH 100 MPH MAX. WT. BOLT CIRCLE (IN.) BOLT SIZE (IN. X IN. X IN.) APPROX. SHIP WT. (LBS.) SSAH 10 4C 10 4 x 10 0.125 13.1 9.9 7.5 100 8.5 - 10 3/4 x 18 x 3 48 SSAH 12 4C 12 4 x 12 0.125 9.6 7.0 5.1 100 8.5 - 10 3/4 x 18 x 3 53 SSAH 14 4C 14 4 x 14 0.125 7.0 4.9 3.3 100 8.5 - 10 3/4 x 18 x 3 57 SSAH 15 4C 15 4 x 15 0.125 6.0 4.0 2.6 100 8.5 - 10 3/4 x 18 x 3 60 SSAH 16 4C 16 4 x 16 0.125 5.0 3.2 1.9 100 8.5 - 10 3/4 x 18 x 3 62 SSAH 16 4G 16 4 x 16 0.188 8.9 6.2 4.3 150 8.5 - 10 3/4 x 30 x 3 86 SSAH 18 4C 18 4 x 18 0.125 3.4 1.8 0.7 100 8.5 - 10 3/4 x 18 x 3 67 SSAH 18 4G 18 4 x 18 0.188 6.8 4.5 2.9 100 8.5 - 10 3/4 x 30 x 3 93 SSAH 18 5G 18 5 x 18 0.188 12.6 8.8 6.1 150 9.312 - 10 3/4 x 30 x 3 108 SSAH 20 4G 20 4 x 20 0.188 5.0 3.0 1.6 150 8.5 - 10 3/4 x 30 x 3 100 SSAH 20 5G 20 5 x 20 0.188 9.9 6.6 4.2 175 9.312 - 10 3/4 x 30 x 3 117 POLE DATA SHAFT BASE SIZE BOLT CIRCLE A BOLT PROJECTION B BASE SQUARE C TEMPLATE DESCRIPTION ANCHOR BOLT DESCRIPTION 4"C 8.5" - 10" 3.5" 11.688" ABTEMPLATE PJ50055 AB18-0 4"G 8.5" - 10" 3.5" 11.688" ABTEMPLATE PJ50055 AB30-0 5" 9.312" - 10" 3.5" 11.688" ABTEMPLATE PJ50056 AB30-0 B Two-piece cast aluminum cover Notes INSTALLATION NOTES: Factory-supplied templates must be used when setting anchor bolts. Lithonia Lighting will not accept claim for incorrect anchorage placement due to failure to use Lithonia Lighting factory templates. Do not erect poles without having fixtures installed. If poles are stored outside, all protective wrapping must be removed immediately upon delivery to prevent finish damage. Hinge base poles without handholes will be drilled for the first fixture 90 degrees to the right of the hinge. When a handhole is specified as an adder, the first fixture drilling will be 90 degreees to the right of the handhole. If the customer has different fixture drilling orientation requirements, please specify that on the purchase order. C A 3/4" Solid aluminum pivot rod Hinge direction "A" side of pole Trapped 3/8" - 16 for ground connector Two piece cast Aluminum cover Intended Use Square Straight Aluminum Hinged light pole with up to 20 foot mounting heights. Best used where maintenance access is limited. Features is heat treated to a T6 temper to provide maximum strength is circumferentially welded to the top and bottom of the shaft and tilting section to ensure maximum support allow ease of access to wiring top "PT" poles to prevent intrusion of moisture or environmental contaminants Polyester powder that meets 5A and 5B classifications of ASTM D3359 and is customizable with a variety of colors

Previous Page
Next Page