Product Selection Guide Page 462 Product Selection Guide-11th Edition

PRODUCT INFORMATION PSG11 462 OPTIONS & ACCESSORIES www.lithonia.com Ballast/Transformer ADALI Advance ROVR electronic controllable ballast utilizing digital addressable lighting interface (DALI) protocol. Requires four-pin lamp (120V or 277V only.) ADCF Advance electronic fluorescent ballast. Requires four-pin lamp (120V or 277V only.) ADEZ Advance Mark X electronic line voltage control dimming ballast. (120V or 277V; 18DTT, 26DTT, 18TRT, 26TRT, 32TRT, 42TRTor 57TRT only.) Requires four-pin lamp. Minimum dimming level 5%. ADZT Advance Mark VII electronic 0-10 VDC dimming ballast. (120V or 277V.) Requires four-pin lamp. Minimum dimming level 5%. ECOS Lutron EcoSystem electronic dimming ballast, 120V - 277V. Must be wattage specific. Minimum dimming level 5%. OSCF OSRAM SYLVANIA electronic fluorescent ballast. Requires four-pin lamp. TUBCF Universal Lighting Technologies electronic ballast. Requires four-pin lamp. SDT Stepdown transformer (277V to 120V; 300W max). RIF1 Radio interference filter. Inductive capacitor circuit designed to minimize interference from feedback into line. (120V through 347V, 50 Hz or 60 Hz.) BDP Ballast disconnect plug meets codes that require in-fixture disconnect. DS Dual switching. CW20 Cold-weather fluorescent ballast; -20 F starting DMHL3 Lutron Hi-Lume electronic 3-wire line voltage control dimming ballast. (120V or 277V; 26TRT or 32TRT only.) Minimum dimming level 1%. 2W5 Lutron Tu-Wire electronic dimming ballast. NEPP Interface for Sensor Swtich nLight network with integral power supply. Refer to TN-623-01. Not available with 347V. Emergency EL Emergency battery pack with integral test switch. Ships standard for one-lamp operation. For two-lamp emergency operation,consult installation instructions or factory. ELR Emergency battery pack with remote test switch. Ships standard for one-lamp operation. For two-lamp emergency operation,consult installation instructions or factory. ELHL IOTA I-420-R High lumen output emergency battery pack. Internal test switch provided. Maximum average lumen output is 1300 (42W). ELRHL IOTA I-420-EM-B High lumen output emergency battery pack. Remote test switch provided. Maximum average lumen output is1300 (42W). ELRHL2LP Emergency battery pack with remote test switch. Operates two 26W or two 42W CFL lamps in emergency mode with battery back-up in case of power disruption. Average output is 2,600 lumens for two 26W lamps; average output is 2,800 lumens for two 42W lamps. ELRSD Emergency battery pack with remote test swtich and self-diagnostics module. Operates one lamp in emergency mode with battery back-up in case of power disruption. Self-diagnostic module evaluates AC to DC transfer, charging and battery condition for five minutes every 30 days and 30 minutes every six months. BGTD Bodine GTD generator transfer device. Factory installed on fixture; senses loss of normal power and switches to auxiliarygenerator to power fixture for egress lighting. Fusing GMF Single, slow-blow fuse. (120V, 277V or 347V only.) For use with fluorescent fixtures only. GLR Single, fast-blow fuse. Fluorescent only. SF Single fuse. (120V, 277V or 347V only.) Trim TRW White painted flange. TRBL Black painted flange. Lamp WLP Lamp (shipped separately). LPSP Spot lamp (shipped separately). LPFL Flood lamp (shipped separately). Miscellaneous CP Chicago plenum. Accessories CTE6 Use when ceiling thickness is greater than 1"-1-1/2" . Maximum thickness 2" . For use with 6"vertical reflectors only. CTE8 Use when ceiling thickness is greater than 1"-1-1/2" . Maximum thickness 2" . For use with 8"vertical reflectors only. SCA Sloped ceiling adapter. Compatible with 8"and 6"commercial fixtures. Available in 5 increments, 10 to 30. White only. See chart for fixture compatibility. Ex: SCA6 15D CTR6 8-3/4"O.D. Use with F6 and 6 Series trims. Compatible with all 7-5/8"flanged trims only. Options LITHONIA LIGHTING COMMERCIAL DOWNLIGHTING

Previous Page
Next Page