Product Selection Guide Page 170 Product Selection Guide-11th Edition

Luminaire Number of lamps in cross section Lamp type Reflector Shielding (AEM2 and EZM2 only) Luminaire row length Maximum section length Voltage Ballast type Number of emergency modules AEM1 AEM2 EZM1 EZM2 1 2 28T5 28W T5 54T5HO 54W T5HO WHR White reflector SPR Specular reflector (blank) Partial perforation CWIN Continuous perforation X FT 4' increments R4 4' section(s) R8 8' section(s) R12 12' section(s) 120 277 347 (Not available with T5) GEB10 <10% THD Electronic ADEZ* Advance Mark 10 dim (T5HO) ADZT* Advance Mark 7 0-10V dim DMHL3D* Lutron Hi-Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. (blank) None 1SE 1 section 2SE 2 sections XSE X sections Emergency type* Switching Lamp color Mounting type Overall suspension Finish Options (blank) None EC Emergency circuit EL Emergency battery pack (Not available with U2 or U3; not available in 347V) EN Emergency battery pack w/night light circuit (Not available with U2 or U3; not available in 347V) *EL and EC are installed in last 4' of luminaire sections and are not available together. Separate feed required for each EL, EC or EN unless ELH is specified. SCT Single circuit DCT Dual circuit L/LP No lamp LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. F1/ T-bar ceiling (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) 12 12" 15 15" 18 18" 21 21" 24 24" XX XX" Overall suspension is measured from ceiling to bottom of luminaire. C110 Painted aluminum (low gloss) C518 White (fine- textured low gloss) C099 Custom finish ACG Adjustable cable grippers BLK Black cord, cord manager and canopy CP Chicago plenum (available with F1A only) DL Damp location label DU Dust cover GLR Fusing (fast blow) GMF Fusing (slow blow) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone NYC New York City code OJB Offset junction box SLP Sloped ceiling (for 10-45, must be specified along with F2, ACG and OJB options) XXXX Smart luminaire (see note above) PRODUCT INFORMATION PSG11 170 AERO AND ENZO Construction 6 1/2" x 2 3/16" one-piece cold-rolled steel housing with flat end plate. Reflectors Die-formed highly reflective white or specular reflector. Shielding AEM2, EZM2: Die-punched, perforated hole pattern. Finish Fine-textured, white or aluminum paint. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and cUL Listed. Luminaire Length 4', 8', and 12' lengths in a single section for exact suspension spacing of 4', 8', and 12'. For total luminaire length add 1/16" for each end cap. Using internal joiners, 4', 8', and 12' sections can be joined to form longer-length luminaires. Smart Luminaire Integrated occupancy sensing, daylight detection and/or network control available. Limitations may apply, see luminaire specification on website for details and option code. AERO AND ENZO Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions are shown in inches (centimeters) unless otherwise noted. ADDITIONAL INFORMATION For additional product information, visit www.peerlesslighting.com. Suspended www.peerlesslighting.com PEERLESS ORDERING INFORMATION Specifications subject to change. Example: AEM1 1 54T5HO WHR 40FT R12 277 GEB10 2SE EL SCT LP841 F1/24 C518 GLR AEM Aero 6-1/2 (16.5) 2-3/16 (5.6) EZM Enzo 6-1/2 (16.5) 2-3/16 (5.6) AEM1 AEM2 AEM2-CWIN EZM1 EZM2 EZM2-CWIN

Previous Page
Next Page