Product Selection Guide Page 164 Product Selection Guide-11th Edition

Luminaire Number of lamps in cross section Lamp type Reflector Shielding Luminaire row length Maximum section length Voltage Ballast type Number of emergency modules NRM9 1 2 3 1 2 28T5 28W T5 54T5HO 54W T5HO 32 32W T8 SPR Specular reflector WHR White reflector FST Frosted diffuser X FT 4' increments R4 4' section(s) R8 8' section(s) 120 277 347 (Not available with 28T5) GEB10 <10% THD Electronic OS5C* Osram Line or 0-10V (T8) ADEZ* Advance Mark 10 dim (T8, T5HO) ADZT* Advance Mark 7 0-10V dim DMHL3D* Lutron Hi-Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. (blank) None 1SE 1 section 2SE 2 sections XSE X sections Emergency type* Switching Lamp color Mounting type Overall Suspension Finish Options (blank) None EC Emergency circuit EL Emergency battery pack (Not available in 347V) EN Emergency battery pack w/ night light circuit (Not available in 347V) *Emergency type is installed in last 4' of luminaire sections. Separate feed required unless ELS or ELS2 is specified. SCT Single circuit DCT Dual circuit L/LP No lamp L/LPE No lamp. Wired for energy saving T8 lamps LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. F1/ T-bar ceiling (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) F3/ Rigid stem 12 12" 15 15" 18 18" 21 21" 24 24" XX XX" Overall suspension is measured from ceiling to bottom of luminaire. C041 White white (low gloss) C100 Satin anodized finish C099 Custom finish ACG Adjustable cable grippers BLK Black cord, cord manager and canopy (not available with F3) CP Chicago plenum (available with F1A only) DL Damp location label DU Dust cover (not available with 3-lamp T5HO) GLR Fusing (fast blow) GMF Fusing (slow blow) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone OJB Offset junction box SCEP Sculptured end cap (available with T5/T5HO only) SLP Sloped ceiling (for 10-45, must be specified along with F2, ACG and OJB options) XXXX Smart luminaire (see note above) PRODUCT INFORMATION PSG11 164 NARO ADDITIONAL INFORMATION For additional product information, visit Suspended PEERLESS Construction Nominal 4 1/2"W x 2 1/4"H (T5/T5HO) and 5 1/4"W x 2 3/4"H (T8) extruded aluminum housing. Die-cast aluminum end caps are mechanically attached with no exposed fasteners. Reflectors Semi-specular high reflectance aluminum or high reflectance white painted steel. Select semi-specular (SPR) for a wide distribution and maximum row spacing. Select white (WHR) for narrow applications (i.e. corridors) to soften side wall shadows. Shielding Frosted acrylic diffuser. Finish White, polyester powder painted or satin anodized. Satin anodized consists of satin anodized housing with end caps painted C110 (aluminum) to match. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and cUL Listed. Luminaire Length 4' and 8' lengths in a single section. For total luminaire length add 1/2" for each standard end cap or 4-" for each sculptured end cap (T5/T5HO only). Using internal joiners, 4' and 8' sections can be joined to form longer rows. Eco-Friendly Packaging 100% post-consumer recycled cardboard box, 100% recycled cardboard cradles and kraft paper tape. Biodegradable, protective luminaire bag. Smart Luminaire Integrated occupancy sensing, daylight detection and/or network control available. Limitations may apply, consult factory for details and option code. 5-" 13.3 Drawings are for dimensional detail and may not represent actual mechanical configuration. Dimensions are shown in inches (centimeters) unless otherwise noted. NRM9 T5 (1, 2, 3) T5, T5HO NRM9 T8 (1, 2) T8 2-" (5.7) 2-" (5.7) 4-" (11.4) ORDERING INFORMATION Specifications subject to change. Example: NRM9 2 28T5 SPR FST 40FT R8 277 GEB10 DCT LP835 F1/18 C100 Configurations Mitered corner, "X" and "T" connectors available for suspended configurations (T5/T5HO only). Additional pattern connector details available at NRM9 T8 NRM9 T5 Sculptured End Cap

Previous Page
Next Page