Product Selection Guide Page 159 Product Selection Guide-11th Edition

Luminaire Number of lamps in cross section Lamp type Reflector Shielding (CRW4 only) Luminaire row length Maximum section length Voltage Ballast type Number of emergency modules CRW1 CRW2 CRW3 CRW4 CRW7 1 2 28T5 28W T5 54T5HO 54W T5HO 32 32W T8 WHR White reflector (standard) SPR Specular reflector (blank) Standard Perforation Perf Continuous Perforation Top Edge (CRW4 only) X FT 4' increments R4 4' section(s) R8 8' section(s) R12 12' section(s) 120 277 347 GEB10 <10% THD Electronic OS5C* Osram Line or 0-10V (T8) ADEZ* Advance Mark 10 dim (T8, T5HO) DMHL3D* Lutron Hi-Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. (blank) None 1SE 1 section 2SE 2 sections XSE X sections Emergency type* Switching Lamp color Finish Shielding Options (blank) None EC Emergency circuit EL Emergency battery pack (Not available in 347V) EN Emergency battery pack w/night light circuit (Not available in 347V) *EL and EC are installed in last 4' of luminaire sections and are not available concurrently with each other. Separate feed required for each EL or EC unless ELH is specified. SCT Single circuit DCT Dual circuit L/LP No lamp L/LPE No lamp. Wired for energy saving T8 lamps. LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. WHR White reflector (standard) SPR Specular reflector C110 Painted aluminum (low gloss) C210 White white (fine-textured low gloss) C099 Custom finish DL Damp location label DU Dust cover GLR Fusing (fast blow) GMF Fusing (slow blow) SCEP Sculptured end cap PRODUCT INFORMATION 159 PSG11 ORDERING INFORMATION Specifications subject to change. Example: CRW1 1 54T5HO WHR 40FT R12 277 GEB10 SCT LP835 C210 SCEP Construction Housing is formed from one-piece cold-rolled steel. Flat end plate standard. Sculptured die-cast aluminum end cap is optional. Reflectors Die-formed highly reflective white or specular reflector. Shielding CRW2: Die-punched 3/8" square windows on lower housing with acrylic opal diffuser overlay. CRW3: Die-punched perforated window on lower housing with acrylic opal diffuser overlay. CRW4: Window opening with straight blade baffle and white opal overlay. CRW7: Die-punched perforations on lower housing with acrylic opal diffuser overlay. Finish Fine-textured, white or aluminum polyester powder paint. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and cUL Listed. Luminaire Length CRW1 T5/T5HO, CRW2 T5/T5HO: Nominal 4', 8', and 12' sections form row lengths. Actual section length is 11 5/8" per nominal foot specified. For total run length, add 1/16" for each flat end plate or 4" for each sculptured end cap. For longer run lengths, sections are attached using internal joiners. Consult factory for 2' and 3' individual sections. CRW1 T8, CRW2 T8, CRW3, CRW4, CRW7: Nominal 4', 8', and 12' sections form row lengths. Consult factory for 2' and 3' sections. For total run length, add 1/16" for each flat end plate or 4" for each sculptured end cap. For longer run lengths, sections are attached using internal joiners. Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions are shown in inches (centimeters) unless otherwise noted. ADDITIONAL INFORMATION For additional product information, visit www.peerlesslighting.com. CERRA WALL Wall www.peerlesslighting.com PEERLESS Configurations Cast aluminum tenon, inside and outside "L" connectors available for wall configurations. Additional pattern connector details available at PeerlessLighting.com. CRW3 CRW2 CRW1 CRW7 CRW4 7-5/8 (19.4) 2-3/4 (7.0)

Previous Page
Next Page