Product Selection Guide Page 155 Product Selection Guide-11th Edition

Luminaire Number of lamps in cross section Lamp type Shielding Luminaire row length Maxium section length Voltage Ballast type Number of emergency modules IRDW8 IADW8 ICDW8 1 28T5 28W T5 54T5HO 54W T5HO 32 32W T8 OPI Intermediate brightness opal diffuser OPD Standard brightness opal diffuser X FT 4' increments R4 4' section(s) R8 8' section(s) R12 12' section(s) 120 277 347 GEB10 <10% THD Electronic OS5C* Osram Line or 0-10V (T8) ADEZ* Advance Mark 10 dim (T8, T5HO) ADZT* Advance Mark 7 0-10V dim DMHL3D* Lutron Hi-Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. (blank) None 1SE 1 section 2SE 2 sections XSE X sections Emergency type* Switching Lamp color Finish Options (blank) None EC Emergency circuit EL Emergency battery pack (Not available in 347V) EN Emergency battery pack w/ night light circuit (Not available in 347V) *Emergency type is installed in last 4' of luminaire sections. Separate feed required unless ELS or ELS2 is specified. SCT Single circuit L/LP No lamp L/LPE No lamp. Wired for energy saving T8 lamps. LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. C041 White white (low gloss) C100 Satin anodized finish C099 Custom finish DL Damp location label GLR Fusing (fast blow) GMF Fusing (slow blow) NYC New York City code PRODUCT INFORMATION 155 PSG11 Construction Nominal 4" x 7" (4" x 6" for IRDW8) extruded aluminum spine and nominal 4' one-piece aluminum baffle assemblies. Steel and die-cast aluminum sculptured end cap. Reflectors White painted center reflector (nominal 90% reflectance). Shielding Straight blade baffles with intermediate or standard brightness opal acrylic diffuser overlay. Finish Satin anodized or white polyester powder paint. Satin anodized finish consists of satin anodized housing, clear-coated aluminum baffles and end caps painted C110 to match. Note that clear-coated aluminum baffles retain the slight imperfections and characteristics of the raw aluminum source material. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and cUL Listed. Luminaire Length 4', 8', and 12' lengths in a single section for exact suspension spacing of 4', 8' and 12'. For total luminaire length, add 1 3/8" for each end cap. Using internal joiners 4', 8', and 12' sections can be joined to form longer rows. Individual 2' and 3' units also available, consult factory ICETRAY Direct Wall Wall www.peerlesslighting.com PEERLESS Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions are shown in inches (centimeters) unless otherwise noted. ADDITIONAL INFORMATION For additional product information, visit www.peerlesslighting.com. ORDERING INFORMATION Specifications subject to change. Example: IADW8 1 28T5 OPI 24FT R8 120 GEB10 SCT LP841 C100 Configurations Tenon inside, outside "L" and straight connectors available for suspended configurations. Additional pattern connector details available at PeerlessLighting.com. IRDW8 ICDW8 IADW8 IRDW8 Rectangular Wall 3-7/8 (9.8) 3/8 (1.0) 6-3/8 (16.2) IADW8 Angular Wall 3-7/8 (9.8) 3/8 (1.0) 7 (17.8) ICDW8 Curved Wall 3-7/8 (9.8) 3/8 (1.0) 7-1/8 (18.1)

Previous Page
Next Page