Product Selection Guide Page 154 Product Selection Guide-11th Edition

Luminaire Ceiling type Number of lamps in cross section Lamp type Shielding Luminaire row length Maximum section length Voltage Ballast type Number of emergency modules IRDM8 IADM8 ICDM8 (blank) Suspended S Surface mounted 1 2 28T5 28W T5 54T5HO 54W T5HO 32 32W T8 OPD Straight blade baffle with opal diffuser (Not available with 2-lamp cross section) SBP Straight blade baffle with side perforated shield X FT 4' increments R4 4' section(s) R8 8' section(s) R12 12' section(s) 120 277 347 GEB10 <10% THD Electronic OS5C* Osram Line or 0-10V (T8) ADEZ* Advance Mark 10 dim (T8, T5HO) ADZT* Advance Mark 7 0-10V dim DMHL3D* Lutron Hi-Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. (blank) None 1SE 1 section 2SE 2 sections XSE X sections Emergency type* Switching Lamp Color Mounting type Overall Suspension Finish Options (blank) None EC Emergency circuit EL Emergency battery pack (Not available in 347V) EN Emergency battery pack w/ night light circuit (Not available in 347V) *Emergency type is installed in last 4' of luminaire sections. Separate feed required unless ELS or ELS2 is specified. SCT Single circuit DCT Dual circuit L/LP No lamp L/LPE No lamp. Wired for energy saving T8 lamps. LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. F1/ T-bar ceiling (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) F3/ Rigid stem 12 12" 15 15" 18 18" 21 21" 24 24" XX XX" Overall suspension is measured from ceiling to bottom of luminaire. C041 White white (low gloss) C100 Satin anodized finish C099 Custom finish ACG Adjustable cable grippers BLK Black cord, cord manager and canopy (not available with F3) CP Chicago plenum (available with F1A only) DL Damp location label GLR Fusing (fast blow) GMF Fusing (slow blow) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone OJB Offset junction box NYC New York City code SCEP Sculptured end cap SLP Sloped ceiling (for 10-45, must be specified along with F2, ACG and OJB options) XXXX Smart luminaire (see note above) PRODUCT INFORMATION PSG11 154 ICETRAY Construction Nominal 7" x 4" (6" x 4" for IRDM8) extruded aluminum spine and nominal 4' one-piece aluminum baffle assemblies. Steel and die-cast aluminum sculptured end cap. Reflectors White painted center reflector (nominal 90% reflectance). Perforated side reflector/shield. Finish Satin anodized or white polyester powder paint. Satin anodized finish consists of satin anodized housing, clear-coated aluminum baffles and end caps painted C110 to match. Note that clear-coated aluminum baffles retain the slight imperfections and characteristics of the raw aluminum source material. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and cUL Listed. Luminaire Length 4', 8', and 12' lengths in a single section for exact suspension spacing of 4', 8' and 12'. For total luminaire length, add 1 3/8" for each end cap. Using internal joiners 4', 8', and 12' sections can be joined to form longer rows. Smart Luminaire Integrated occupancy sensing, daylight detection and/ or network control available. Limitations may apply, see specification sheets on website for details and option code. ICETRAY Direct Suspended www.peerlesslighting.com PEERLESS Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions are shown in inches (centimeters) unless otherwise noted. ADDITIONAL INFORMATION For additional product information, visit www.peerlesslighting.com. Configurations Tenon "L", "T", "X" and straight connectors available for suspended configurations. Additional pattern connector details available at PeerlessLighting.com. ORDERING INFORMATION Specifications subject to change. Example: ICDM8 S 1 54T5HO OPD 12FT R8 277 GEB10 SCT LP835 C041 IRDM8 Rectangular with SBP Perforated Side Shield 3-7/8 (9.8) 6-3/8 (16.2) 7 (17.8) 3-7/8 (9.8) IADM8 Angular with SBP Perforated Side Shield ICDM8 Curved with OPD Opal Diffuser and S Surface Mounted 3-7/8 (9.8) 3/8 (1.0) 7-1/8 (18.1)

Previous Page
Next Page