Product Selection Guide Page 136 Product Selection Guide-11th Edition

Luminaire Number of lamps in cross section Lamp type Distribution (nominal) Reflector Shielding (SPM4 only) Luminaire row length Maximum section length Voltage Ballast type SPM4 SPM9 1 2 3 28T5 28W T5 54T5HO 54W T5HO 32 32W T8 (blank) 65% up, 35% down standard 40/60* 40% up, 60% down 20/80* 20% up, 80% down 0/100* 100% down CLI Center lamp isolator (Available with 3-lamp cross section only) *Nominal distribution, refer to photometric test for exact distribution. WHR White reflector (blank) None OPD Opal diffuser X FT 4' increments R4 4' section(s) R8 8' section(s) R12 12' section(s) 120 277 347 GEB10 <10% THD Electronic OS5C* Osram Line or 0-10V (T8) ADEZ* Advance Mark 10 dim (T8, T5HO) ADZT* Advance Mark 7 0-10V dim DMHL3D* Lutron Hi-Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. Number of emergency modules Emergency type Switching Lamp color Mounting type Overall suspension Finish Options (blank) None 1SE 1 section 2SE 2 sections XSE X sections (blank) None EC Emergency circuit EL Emergency battery pack (Not available in 347V) EN Emergency battery pack w/night light circuit (Not available in 347V) *EL and EC are installed in last 4' of luminaire sections. Separate feed required unless ELS or ELS2 is specified. SCT Single circuit DCT Dual circuit L/LP No lamp L/LPE No lamp. Wired for energy saving T8 lamps. LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. F1/ T-bar ceiling (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) 24 24" 48 48" 72 72" 96 96" XX XX" Overall suspension is measured from ceiling to bottom of luminaire. C032 White white (high gloss) C099 Custom finish CP Chicago plenum (available with F1A only) DL Damp location label DU Dust cover (Not available with 3-lamp T5/T5HO) GLR Fusing (fast blow) GMF Fusing (slow blow) IND Individual luminaire (factory installed end caps and power cord, hanging hardware in box) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone NYC New York City code OJB Offset junction box SLP Sloped ceiling (for 10-45, must be specified along with F2, ACG and OJB options) XXXX Smart luminaire (see note above) PRODUCT INFORMATION PSG11 136 STAPLE Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions (if provided) are shown in inches unless otherwise noted. ADDITIONAL INFORMATION For additional product information, visit www.peerlesslighting.com. www.peerlesslighting.com PEERLESS Construction Nominal 8 1/2" x 2 3/8" rectangular housing is formed from cold-rolled steel. Die-cast aluminum end caps are mechanically attached with no exposed fasteners. Reflectors Formed, pre-finished white reflector. Shielding SPM4: Injection molded acrylic baffle with opal diffuser option. SPM9: Acrylic lens. Finish White gloss powder paint standard. Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and cUL Listed. Luminaire Length 4', 8' and 12' lengths in a single section for nominal suspension spacing of 4', 8' and 12'. For total luminaire length, add 1 1/8" for each end cap. Using internal joiners, 4', 8' and 12' sections can be joined to form longer length luminaires. Installation Features Y-hangers with adjustable cables come standard to simplify luminaire leveling across the width and length. Individual 4', 8' and 12' luminaires can be ordered with end caps and power cords pre-installed and hanging hardware included in the luminaire packaging to reduce overall installation time (option IND). Smart Luminaire Integrated occupancy sensing, daylight detection and/or network control available. Limitations may apply, see luminaire specification on website for details and option code. 8 1 / 2 " 2 3 / 8 " 8 1 / 2 " 2 3 / 8 " SPM4 Baffle (1, 2, 3) T5, T5HO, T8 SPM9 Lens (1, 2, 3) T5, T5HO, T8 ORDERING INFORMATION Specifications subject to change. Example: SPM4 2 54T5HO WHR 40FT R12 277 GEB10 DCT LP835 F1/18 C032 SPM9 SPM4 PRODUCT INFORMATION Suspended

Previous Page
Next Page