Product Selection Guide Page 134 Product Selection Guide-11th Edition

Luminaire Number of lamps in cross section Lamp type Reflector Distribution 1 (BRM4 and BRM9; not available with DU option) Shielding (BRM3, BRM4 only) Baffle (BRM4 only) Luminaire row length Voltage Ballast type Switching BRM1 BRM3 BRM4 BRM7 BRM9 1 2* 3 *BRM7 available in 2 lamp only. 28T5 28W T5 (Not available in 347V) 54T5HO 54W T5HO 32 32W T8 SPR Specular reflector (blank) Standard; 65% up; 35% down 20/80 2 20% up, 80% down 40/60 2 40% up, 60% down (BRM4 only) 0/100 2,3 0% up, 100% down CLI 4 Center lamp isolater (BRM4 only) 1 BRM9: Available with SSH option only. Nominal distribution, refer to photometric tests for exact distribution. 2 BRM4: Nominal distribution, refer to photometric tests for exact distribution. 3 BRM9: Not available with 3-lamp 54T5HO luminaires. 4 BRM4: Available with 3-lamp cross section luminaires only. (blank) None OPD Opal diffuser overlay (BRM3, BRM4) ODD Opal drop diffuser (BRM9 only) SSH Softshine high performance lens (BRM9) SSB Semi- specular WPB White painted SSP Semi- specular perforated blade WPP White painted perforated blade X FT 4' increments 120 277 347 GEB10 <10% THD Electronic ADEZ* Advance Mark 10 dim (T5HO) ADZT* Advance Mark 7 0-10V dim DMHL3D* Lutron Hi- Lume dim *Not available in 347V. Reference Ballast Wizard on website or consult factory for other options. SCT Single circuit DCT Dual circuit Number of emergency modules Emergency type* Lamp color Mounting Type Overall suspension Finish Options (blank) None 1SE 1 section 2SE 2 sections XSE X sections (blank) None EC Emergency circuit EL Emergency battery pack (Not available in 347V) EN Emergency battery pack w/night light circuit (Not available in 347V) *Emergency type is installed in last 4' of luminaire sections. Separate feed required unless ELS or ELS2 is specified. L/LP No lamp L/LPE No lamp. Wired for energy saving T8 lamps. LP830 3000K 80+ CRI LP835 3500K 80+ CRI LP841 4100K 80+ CRI Available with T5 only: LP830P 3000K 80+ CRI Premier LP835P 3500K 80+ CRI Premier LP841P 4100K 80+ CRI Premier Reference Lamp Chart on website or consult factory for other options. F1/ T-bar ceiling (universal mounting bracket) F1A/ T-bar ceiling (UMB with integrated J-box) F2/ Hard ceiling (horizontal J-box) F3/ Rigid stem 12 12" 15 15" 18 18" 21 21" 24 24" XX XX" Overall suspension is measured from ceiling to bottom of luminaire. C110 Painted aluminum (low gloss) C210 White white (fine- textured low gloss) C099 Custom finish ACG Adjustable cable grippers BLK Black cord, cord manager and canopy (not available with F3) CP Chicago plenum (available with F1A only) DL Damp location label DU Dust cover (BRM1, BRM3, BRM4, BRM9, not available with 3-lamp T5HO cross section) GLR Fusing (fast blow) GMF Fusing (slow blow) MCS Matching feed canopy at support NEPP5D nLight enabled control module per row/zone NYC New York City code OJB Offset junction box SCEP Sculptured end cap SLP Sloped ceiling (for 10-45, must be specified along with F2, ACG and OJB options) XXXX Smart luminaire (see note above) BRUNO PRODUCT INFORMATION PSG11 134 BRUNO www.peerlesslighting.com PEERLESS Construction Nominal 8 1/4" x 1 3/4" rectangular housing is formed from cold rolled steel. Die-cast end caps are mechanically attached with no exposed fasteners. Reflectors Die-formed specular reflector with 95% reflectance. Shielding BRM3: Aluminum, die-formed drop pan with five 2 3/4" cylinder openings of down light feature. Also available with acrylic opal overlay on top of down light openings. BRM4: Choose one of four parabolic baffle options: semi-specular, white painted, semi-specular perforated blade or white painted, perforated blade. Each available with optional acrylic opal overlay. BRM7: Die-punched perforations with acrylic opal diffuser overlay. BRM9: Die-formed drop acrylic diffuser or flush Softshine high-performance lens. Finish Fine-textured, white polyester powder paint is standard. Drop pan on BRM3 is always painted aluminum (C110). Custom colors available, consult factory. Electrical Specify 120V, 277V or 347V. Pre-wired with 16AWG luminaire wires. For special circuiting or wire gauge, consult factory. Plug-in electrical connectors included. UL and CUL Listed. Luminaire Length 4' 3/8", 8' and 12' lengths in a single section for nominal support spacing at 4', 8' and 12'. For total luminaire length, add 5/8" for each flat end cap and 4" for each sculptured end cap. Using internal joiners, 4', 8' and 12' sections can be joined to form longer rows. Smart Luminaire Integrated occupancy sensing, daylight detection and/or network control available. Limitations may apply, see luminaire specification on website for details and option code. PRODUCT INFORMATION Suspended ORDERING INFORMATION Specifications subject to change. Example: BRM1 2 28T5 SPR 40FT R8 277 GEB10 DCT LP835 F1/18 C210 SCEP BRM3 BRM4 BRM7 BRM9 ODD BRM9 SSH 8 1 / 4 " 1 3 / 4 " 8 1 / 4 " 1 3 / 4 " 8 1 / 4 " 1 3 / 4 " BRM1 Indirect (1, 2, 3) T5, T5HO, T8 BRM3 Holes BRM4 I/D BRM9 Diffuser (1, 2, 3) T5, T5HO, T8 BRM7 Partial Perf (2) T5, T5HO, T8 Drawings are for dimensional detail only and may not represent actual mechanical configuration. Dimensions (if provided) are shown in inches unless otherwise noted. ADDITIONAL INFORMATION For additional product information, visit www.peerlesslighting.com. Configurations Tenon "L", "T", "X" and straight connectors available for suspended configurations. Additional pattern connector details available at PeerlessLighting.com.

Previous Page
Next Page